Android Oscilloscope
OBD2 Engine Rev Counter
OBD2 Diagnostic app
TFT Clock and Thermometer
WiFi, Ethernet
WiFi Thermometer
WiFi ESP8266
Doorbell with SD / EEPROM
SD FAT16/32 for .bmp
PETIT FAT bmp Display
TFT Timer, Thermometer
TFT Oscilloscope
SD Talking Clock
Android Talking Clock
SD Sound Recorder
SD FAT32 wav Player
SD Arduino Recorder
LED Thermometer
LED Timer
LCD Timer
TFT 10MHz Counter
100KHz Counter For PC
1MHz Counter For PC
8 Digits LED Counter
Scope Screen Counter
LCD Module Counter
LCD Arduino Counter
6MHz Android Counter
NIXIE Android Counter
Bluetooth Counters
USB Counter
USB TFT display BMP
USB DS18B20 Sensor
USB Thermometer
USB Meter
USB Oscilloscope
USB Input-Output
USB Input-Output Android
USB 16x2 LCD
Serial TFT Text
Serial Inputs Outputs
Serial Port LCD
MCP3201 on Serial Port
Serial Thermometer
Analogue Signal to Serial
Serial Thermostat
MCP3201 on LPT
Analogue Signal to LPT
LCD Display on LPT
Water Softener
HP Stream 7 docking
3.7V to 5V
Solar Charger
Infrared Decoder
PIC Music
Code Lock
Code Lock with LCD
HOME   Technical Tips

HP TABLET STREAM 7

Project to create a docking station for HP Stream tablet with Windows 8.1 . This enables the tablet to be charged while using the USB to interface a mouse, keyboard and other USB devices. The version with a relay is an option for automatic switch to DEVICE input.
When the tablet detects external 5V at the USB connector and D+ linked to D- and the battery is below 95% it charges the battery with a current of 800 - 1200 mA. This charging state is set and will persist until the external 5V is removed. When the tablet is ON the charging will go on until battery reaches 95% then charge will switch on and off to keep the battery at 95%. When tablet is shut down the battery is charged up to 100%.

OTG switch is on for battery only operation. When the OTG switch is on charge is disabled by the tablet.

When the tablet is in charging state D+ and D- can be switched to the data lines of the USB device, the tablet then communicates with the USB devices. The USB devices are powered by the external 5V (charger).
USB Device can be a USB hub.
With manual switch circuit version switch to CHARGE position then connect the charger. After the tablet indicates that it is charging switch to DEVICE to enable the use of the USB devices.

Docking Station with manual switch

 

Docking Station with auto switch

Circuit Description
See also Technical Tips

Charger USB connector is a Micro B Female. Tablet USB connector is a 5 pins Micro B Male. USB Device is a type A Female. To identify the 5V, D+, D- and ground pins I used these pinout drawings. http://pinouts.ru/Slots/usb_pinout.shtml   http://pinouts.ru/PortableDevices/micro_usb_pinout.shtml
The transistor is a 5 seconds delay timer.
Relay is a 5V coil with a changeover contact. The smaller the relay the better. A relay is used because the USB bus is a high frequency signal.
Leads should be kept short because of the high currents on power leads and high frequency in the data lines.

 






30.09.2016 - 14:16
Name: Benjamin
Comment: Toda, I will try it as soon i get my OTG cable

29.09.2016 - 21:05
Name: Moty
Comment: Shana Tova Benjamin, yes, you can connect to the OTG a webcam and record video using MS Movie Maker or any other program or app.

29.09.2016 - 17:24
Name: Benjamin
Comment: Can external webcan be connected by OTG to the tablet and the video saved? Toda, Shana Tova!!!!

moty22.co.uk  2008-2020